Publications

Purpose

Explicitly monitoring the need, use and satisfaction of assistive product (AP) provision is essential to support population health and healthy longevity in ageing/aged countries, like Korea. We present findings from the 2017 Korea National Disability Survey (NDS) on AP access and compare them to international averages, introducing Korea’s data into the wider coherence of global AP research.

Materials and methods

Using data from Korea’s 2017 NDS, surveying 91,405 individuals, we extracted and calculated AP access indicators, including needing, having, using and being satisfied with 76 unique APs, by functional difficulty and product type. We compared satisfaction and unmet need between the National Health Insurance System (NHIS) and alternative provision services.

Results

Prosthetics and orthotics had high rates of under-met need, and lower satisfaction rates, from 46.9% to 80.9%. Mobility APs overall had higher rates of under-met need. There was either low (<5%) or no reported need for most digital/technical APs. Among main products, those provided through the NHIS had lower unmet need (26.4%) than through alternative providers (63.1%), though satisfaction rates were similar (p < .001).

Conclusions

The Korean survey findings align with global averages calculated in the Global Report on Assistive Technology. Low reported needs for certain APs may reflect low awareness about how these products could benefit users, emphasizing the importance of data collection at each stage of the AP provision process. Recommendations to expand access to APs are given for people, personnel, provision, products, and policy.

Implications for rehabilitation

• Access to assistive products (APs) is an essential part of physical and occupational therapy services and rehabilitation. Monitoring population-level data on disability and AP access can inform policymakers about a key aspect of population health and healthy ageing, and demonstrate the need to expand access by including APs and associated services in primary/universal healthcare packages.
• Stratifying findings about AP access by type of functional difficulty and further by specific device helps identify the populations for whom needs are not being met. These domain-level and device-level indicators inform efforts to support specific groups within the population of people with disabilities, which has implications for how rehabilitation services are provisioned, targeted and made more accessible.

Jamie Danemayer & Myung-Joon Lim (2023)

Assistive technology in Korea: Findings from the 2017 National Disability Survey, Disability and Rehabilitation: Assistive Technology,

DOI: 10.1080/17483107.2023.2225565

Artificial Intelligence (AI) in Education has been said to have the potential for building more personalised curricula, as well as democratising education worldwide and creating a Renaissance of new ways of teaching and learning. Millions of students are already starting to benefit from the use of these technologies, but millions more around the world are not. If this trend continues, the first delivery of AI in Education could be greater educational inequality, along with a global misallocation of educational resources motivated by the current technological determinism narrative. In this paper, we focus on speculating and posing questions around the future of AI in Education, with the aim of starting the pressing conversation that would set the right foundations for the new generation of education that is permeated by technology. This paper starts by synthesising how AI might change how we learn and teach, focusing specifically on the case of personalised learning companions, and then move to discuss some socio-technical features that will be crucial for avoiding the perils of these AI systems worldwide (and perhaps ensuring their success). This paper also discusses the potential of using AI together with free, participatory and democratic resources, such as Wikipedia, Open Educational Resources and open-source tools. We also emphasise the need for collectively designing human-centered, transparent, interactive and collaborative AI-based algorithms that empower and give complete agency to stakeholders, as well as support new emerging pedagogies. Finally, we ask what would it take for this educational revolution to provide egalitarian and empowering access to education, beyond any political, cultural, language, geographical and learning ability barriers.

Disability stigma in many low- and middle-income countries represents one of the most pervasive barriers preventing people with disabilities from accessing equal rights and opportunities, including the uptake of available assistive technology (AT). Previous studies have rarely examined how disability stigma may be shaped through factors endemic to social interactions, including how the use of assistive technology itself may precipitate or alleviate disability stigma. Through two strands of work, we address this gap. Via a series of focus groups with Kenyans without disabilities (Study 1) and secondary data analysis of consultations with Kenyans with disabilities and their allies (Study 2), we identify shared and divergent understandings of what shapes disability stigma and discrimination. Specifically, Kenyans with and without disabilities were cognizant of how religious/spiritual interpretations of disability, conceptions of impairments as “different” from the norm, and social stereotypes about (dis)ability shaped the experience of stigma and discrimination. Moreover, both groups highlighted assistive technology as an influential factor that served to identify or “mark” someone as having a disability. However, whereas participants without disabilities saw assistive technology purely as an enabler to overcome stigma, participants with disabilities also noted that, in some cases, use of assistive technologies would attract stigma from others.

Barbareschi G, Carew MT, Johnson EA, Kopi N, Holloway C. “When They See a Wheelchair, They’ve Not Even Seen Me”—Factors Shaping the Experience of Disability Stigma and Discrimination in Kenya. International Journal of Environmental Research and Public Health. 2021; 18(8):4272. https://doi.org/10.3390/ijerph...

Living in informality is challenging. It is even harder when you have a mobility impairment. Traditional assistive products such as wheelchairs are essential to enable people to travel. Wheelchairs are considered a Human Right. However, they are difficult to access. On the other hand, mobile phones are becoming ubiquitous and are increasingly seen as an assistive technology. Should therefore a mobile phone be considered a Human Right? To help understand the role of the mobile phone in contrast of a more traditional assistive technology – the wheelchair, we conducted contextual interviews with eight mobility impaired people who live in Kibera, a large informal settlement in Nairobi. Our findings show mobile phones act as an accessibility bridge when physical accessibility becomes too challenging. We explore our findings from two perspective – human infrastructure and interdependence, contributing an understanding of the role supported interactions play in enabling both the wheelchair and the mobile phone to be used. This further demonstrates the critical nature of designing for context and understanding the social fabric that characterizes informal settlements. It is this social fabric which enables the technology to be useable.

Giulia Barbareschi, Ben Oldfrey, Long Xin, Grace Nyachomba Magomere, Wycliffe Ambeyi Wetende, Carol Wanjira, Joyce Olenja, Victoria Austin, and Catherine Holloway. 2020. Bridging the Divide: Exploring the use of digital and physical technology to aid mobility impaired people living in an informal settlement. In Proceedings of the 22nd International ACM SIGACCESS Conference on Computers and Accessibility (ASSETS '20). Association for Computing Machinery, New York, NY, USA, Article 50, 1–13. https://doi.org/10.1145/337362...

Johan Borg, Wei Zhang, Emma M. Smith & Cathy Holloway (2021) Introduction to the companion papers to the global report on assistive technology, Assistive Technology, 33:sup1, 1-2, DOI: 10.1080/10400435.2021.2003658

The supply of and market demand for assistive products (APs) are complex and influenced by diverse stakeholders. The methods used to collect AP population-level market data are similarly varied. In this paper, we review current population-level AP supply and demand estimation methods for five priority APs and provide recommendations for improving national and global AP market evaluation. Abstracts resulting from a systematic search were double-screened. Extracted data include WHO world region, publication year, age-groups, AP domain(s), study method, and individual assessment approach.497 records were identified. Vision-related APs comprised 65% (n = 321 studies) of the body of literature; hearing (n = 59), mobility (n = 24), cognitive (n = 2), and studies measuring multiple domains (n = 92) were proportionately underrepresented. To assess individual AP need, 4 unique approaches were identified among 392 abstracts; 45% (n = 177) used self-report and 84% (n = 334) used clinical evaluation. Study methods were categorized among 431 abstracts; Cross-sectional studies (n = 312, 72%) and secondary analyses of cross-sectional data (n = 61, 14%) were most common. Case studies illustrating all methods are provided. Employing approaches and methods in the contexts where they are most well-suited to generate standardized AP indicators will be critical to further develop comparable population-level research informing supply and demand, ultimately expanding sustainable access to APs.

Jamie Danemayer, Dorothy Boggs, Emma M. Smith, Vinicius Delgado Ramos, Linamara Rizzo Battistella, Cathy Holloway & Sarah Polack (2021) Measuring assistive technology supply and demand: A scoping review, Assistive Technology, 33:sup1, S35-S49, DOI: 10.1080/10400435.2021.1957039

Humanitarian coordination systems increasingly recognize and aim to respond to the needs of people with disabilities within populations affected by crises, spurred on by the UN Convention on the Rights of Persons with Disabilities (CRPD) which was adopted in 2006. Many agencies state their aim to meet the requirements of the CRPD using a “twin track” approach: ensuring the inclusion of people with disabilities in mainstream provision, alongside targeted support for their needs, which may include the need for Assistive Technology (AT). However, there is very little evidence of AT provision in humanitarian settings, which is a specific and urgent need for many people including the elderly and people with disabilities, and an implicit requirement of Article 11 of the CRPD and World Health Assembly resolution on improving access to assistive technology. There is also little evidence of effective mechanisms for AT provision in humanitarian settings. This is despite high and growing levels of unmet AT need in crises, and despite the legally binding requirement in the CRPD to provide AT for those who need it. AT provision faces unique challenges in humanitarian settings. This paper discusses the evidence available in the literature for the scale and quality of AT provision interventions in crises, and what is known about the challenges and facilitators of provision. We conducted a search of the academic literature and retained literature that reported on any form of AT provision following crisis, where international humanitarian response was in place, published in English between January 2010 and June 2020. We found very few examples in that academic literature of systematic and coordinated AT provision at the acute stage of crisis, and even less in the preparedness and post-acute stages. However, it is difficult to assess whether this is the result of insufficient academic attention or reflects a lack of provision. The small body of academic literature that describes AT provision in humanitarian settings paints a picture of small-scale provision, specialized to single types of impairments, and delivered by predominantly by NGOs. We also conducted a search of the gray literature, using the same inclusion criteria, in two countries: Afghanistan and South Sudan (case studies forthcoming). This gray literature provided supplementary evidence of the types of AT providers and AT provision available in those protracted crises. There are very few examples of how AT services can be scaled up (from a very low baseline) and maintained sustainably within a strengthened health system. The literature also describes more examples of provision of assistive products for mobility over assistive products for other impairments. If the paucity of literature on AT provision in humanitarian settings is a reflection of the scale of provision, this implies a deficiency in humanitarian response when it comes to providing people with AT needs with the essential products and services to which they have a right, and which will enable their access to basic, life-saving assistance. We conclude by providing recommendations for urgent actions that the AT and humanitarian community must take to fill this critical gap in the provision of essential products and services for a potentially marginalized and excluded group.

Golnaz Whittaker, Gavin Adam Wood, Giulia Oggero, Maria Kett & Kirstin Lange (2021) Meeting AT needs in humanitarian crises: The current state of provision, Assistive Technology, 33:sup1, S3-S16, DOI: 10.1080/10400435.2021.1934612

For many years, the biggest issue that causes discomfort and hygiene issues for patients with lower limb amputations have been the interface between body and prosthetic, the socket. Often made of an inflexible, solid polymer that does not allow the residual limb to breathe or perspire and with no consideration for the changes in size and shape of the human body caused by changes in temperature or environment, inflammation, irritation and discomfort often cause reduced usage or outright rejection of the prosthetic by the patient in their day to day lives. To address these issues and move towards a future of improved quality of life for patients who suffer amputations, Loughborough University formed the Next Generation Prosthetics research cluster. This work is one of four multidisciplinary research studies conducted by members of this research cluster, focusing on the area of Computer Aided Design (CAD) for improving the interface with Additive Manufacture (AM) to solve some of the challenges presented with improving prosthetic socket design, with an aim to improve and streamline the process to enable the involvement of clinicians and patients in the design process. The research presented in this thesis is based on three primary studies. The first study involved the conception of a CAD criteria, deciding what features are needed to represent the various properties the future socket outlined by the research cluster needs. These criteria were then used for testing three CAD systems, one each from the Parametric, Non Uniform Rational Basis Spline (NURBS) and Polygon archetypes respectively. The result of these tests led to the creation of a hybrid control workflow, used as the basis for finding improvements. The second study explored emerging CAD solutions, various new systems or plug-ins that had opportunities to improve the control model. These solutions were tested individually in areas where they could improve the workflow, and the successful solutions were added to the hybrid workflow to improve and reduce the workflow further. The final study involved taking the knowledge gained from the literature and the first two studies in order to theorise how an ideal CAD system for producing future prosthetic sockets would work, with considerations for user interface issues as well as background CAD applications. The third study was then used to inform the final deliverable of this research, a software design specification that defines how the system would work. This specification was written as a challenge to the CAD community, hoping to inform and aid future advancements in CAD software. As a final stage of research validation, a number of members of the CAD community were contacted and interviewed about their feelings of the work produced and their feedback was taken in order to inform future research in this area.

Bodkin, Troy L. (2017): Specifying a hybrid, multiple material CAD system for next-generation prosthetic design. Loughborough University. Thesis. https://hdl.handle.net/2134/25...;

Transferring independently to and from their wheelchair is an essential routine task for many wheelchair users but it can be physically demanding and can lead to falls and upper limb injuries that reduce the person’s independence. New assistive technologies (ATs) that facilitate the performance of wheelchair transfers have the potential to allow wheelchair users to gain further independence. To ensure that users’ needs are addressed by ATs, the active involvement of wheelchair users in the process of design and development is critical. However, participation can be burdensome for many wheelchair users as design processes where users are directly involved often require prolonged engagement. This thesis makes two contributions to facilitate wheelchair users’ engagement in the participatory design process for ATs, while being mindful of the burden of participation. The first contribution is a framework that provides a modular structure guiding the participatory design process from initial problem identification and analysis to facilitating collaborations between wheelchair users and designers. The framework identifies four factors determining the need and adoption process for ATs: (i) People focuses on the target population, (ii) Person includes personal characteristics, (iii) Activity refers to the challenges associated with the task, and (iv) Context encompasses the effect of the environment in which the activity takes place. The second contribution constitutes a rich picture of personal and external elements influencing real world wheelchair transfers that emerged from four studies carried out to investigate the effect of the framework factors on the design process for ATs. A related outcome based on these contributions is a framing document to share knowledge between wheelchair users and designers to provide focus and promote an equal collaboration among participants.

Barbareschi, Giulia. “YouTransfer, YouDesign : a Participatory Approach to Design Assistive Technology for Wheelchair Transfers / Giulia Barbareschi.” Thesis (Ph.D.)--University College London, 2018., 2018. Print.

Wrist splints are a common treatment for rheumatoid arthritis, however their effectiveness is compromised by patients not wearing splints as often as prescribed. Previous research has identified a number of reasons for non-compliance, but typically lacks insights that could lead to improved splint design.

This thesis investigates the motivators for patients to wear and not wear their wrist splints and, the impact of personalisation of splint appearance on patient wear. The work is based on the premise that digital design and manufacturing processes, such as Computer-Aided Design (CAD) and 3D Printing, can produce bespoke splints on demand.

The research begins with a literature review across the core areas of: splinting, additive manufacture, product appearance and personalisation. This literature review identifies gaps in knowledge from which research questions are established for the work.

The research employs a qualitative, generative design research approach and, follows a codesign framework employing telling, making and enacting tools. The thesis is made up of three studies. The first study is a sensitisation study and uses design probes to prepare the participants for the research and begin exploring the problem space. The second is a comprehensive study into participants splint wear behaviour and uses context mapping and scenario picture card tools to investigate the motivators for participants to wear and not wear wrist splints, along with positive and negative outcomes or wearing/not wearing splints. The final study uses a personalisation toolkit to elicit patient needs for a future wrist splint design and investigate self-reported expectations regarding compliance of patients who used the toolkit.

The research finds that patient compliance is affected by practical and aesthetic limitations of current splints. It identifies 4 motivating factors to wear a splint and 10 motivating factors to not wear a splint. Additionally, it identifies 6 positive outcomes of wearing splints, 6 negative outcomes of wearing splints, 3 positive outcomes of not wearing splints and 3 negative outcomes of not wearing splints. Requirements for an improved splint design are established and form the basis of the design for a prototype personalisation toolkit. Testing of this toolkit reveals that patients are keen to own more than one splint and personalise splints to match the scenario in which it is to be worn. Patients reported that they expected to be more compliant with a personalised splint when compared to their current splint.

Pyatt, Charlotte (2018): Understanding wrist splint user needs and personalisation through codesign. Loughborough University. Thesis. https://doi.org/10.26174/thesi...;

Facial prostheses are artificial devices that replace a missing body part in the facial and neck regions of the body. Defects or deformities in these regions can lead to functional deficiencies; social and psychological effects in addition to cosmetic defects. Restoration or rehabilitation in resource limited countries is usually provided by charities and organisations volunteering assistance overseas, with some training of local staff in the fabrication of these prostheses. Furthermore, these countries typically lack technical knowhow and trained personnel. In industrialised nations maxillofacial prosthetics has developed into a sophisticated medical speciality requiring highly skilled staff and expensive facilities. In resource limited countries surgical procedures may be an option for rehabilitation of these deformities/defects however, they tend to be unavailable or unaffordable and donated prostheses are not suitable. Hence, this research explores, from first principles, the appropriate and affordable local provision of maxillofacial prostheses in resource constrained regions. The investigation provides knowledge on identifying requirements for resource limited areas, resulting in the creation of a guideline constituting priorities, requirements and specifications. It further explores the viability of potentially cheaper, locally available candidate materials via weathering and antimicrobial methods in ascertaining material longevity.

Tetteh, Sophia (2019): Materials for facial prostheses in resource-limited countries. Loughborough University. Thesis. https://doi.org/10.26174/thesi...;

Amongst lower-limb prosthesis wearers, thermal discomfort is a common problem with an estimated prevalence of more than 50%. Overheating does not just create discomfort to the user, but it has been linked to excessive sweating, skin damage caused by a moist environment and friction. Due to impermeable prosthetic components and a warm moist environment, minor skin damage can result in skin infections that can lead to prosthesis cessation, increased social anxiety, isolation and depression. Despite the seriousness of thermal discomfort, few studies explore the issue, with research predominantly constrained to controlled laboratory scenarios, with only one out of laboratory study. In this thesis, studies investigate how thermal discomfort arises and what are the consequences of thermal discomfort for lower-limb prosthesis wearers. Research studies are designed around the principles of presenting lived experiences of the phenomenon and conducting research in the context of participants' real-life activities. A design exploration chapter investigates modifying liner materials and design to create a passive solution to thermal discomfort. However, this approach was found to be ineffective and unfeasible. Study 1 presents a qualitative study which investigates the user experience of a prosthesis, thermal discomfort and related consequences. Study 2 explores limb temperature of male amputees inside and outside the laboratory, with the latter also collecting perceived thermal comfort (PTC) data. Finally, Study 3 investigates thermal discomfort in the real-world and tracks limb temperature, ambient conditions, activities, and experience sampling of PTC. While there were no apparent relationships presented in sensor data, qualitative data revealed that in situations where prosthesis wearers perceived a lack of control, thermal discomfort seemed to be worse. When combined, the studies create two knowledge contributions. Firstly, the research provides a methodological contribution showing how to conduct mixed-methods research to obtain rich insights into complex prosthesis phenomena. Secondly, the research highlights the need to appreciate psychological and contextual factors when researching prosthesis wearer thermal comfort. The research contributions are also converted into an implication for prosthesis design. The concept of 'regaining control' to psychologically mitigate thermal discomfort could be incorporated into technologies by using 'on-demand' thermal discomfort relief, rather than 'always-on' solutions, as have been created in the past.

Williams, Rhys James. “Exploring Thermal Discomfort Amongst Lower-Limb Prosthesis Wearers.” ProQuest Dissertations Publishing, 2020. Print.

Additive Manufacturing (AM) often known by the term three-dimensional printing (3DP) has been acknowledged as a potential manufacturing revolution. AM has many advantages over conventional manufacturing techniques; AM techniques manufacture through the addition of material - rather than traditional machining or moulding methods. AM negates the need for tooling, enabling cost-effective low-volume production in high-wage economies and the design & production of geometries that cannot be made by other means. In addition, the removal of tooling and the potential to grow components and products layer-by-layer means that we can produce more from less in terms of more efficient use of raw materials and energy or by making multifunctional components and products. The proposed Centre for Doctoral Training (CDT) in Additive Manufacturing and 3D Printing has the vision of training the next generation of leaders, scientists and engineers in this diverse and multi-disciplinary field. As AM is so new current training programmes are not aligned with the potential for manufacturing and generally concentrate on the teaching of Rapid Prototyping principles, and whilst this can be useful background knowledge, the skills and requirements of using this concept for manufacturing are very different. This CDT will be training cohorts of students in all of the basic aspects of AM, from design and materials through to processes and the implementation of these systems for manufacturing high value goods and services. The CDT will also offer specialist training on aspects at the forefront of AM research, for example metallic, medical and multi-functional AM considerations. This means that the cohorts graduating from the CDT will have the background knowledge to proliferate throughout industry and the specialist knowledge to become leaders in their fields, broadening out the reach and appeal of AM as a manufacturing technology and embedding this disruptive technology in company thinking. In order to give the cohorts the best view of AM, these students will be taken on study tours in Europe and the USA, the two main research powerhouses of AM, to learn from their international colleagues and see businesses that use AM on a daily basis. One of the aims of the CDT in AM is to educate and attract students from complementary basic science, whether this be chemistry, physics or biology. This is because AM is a fast moving area. The benefits of having a CDT in AM and coupling with students who have a more fundamental science base are essential to ensure innovation & timeliness to maintain the UK's leading position. AM is a disruptive technology to a number of industrial sectors, yet the CDTs industrial supporters, who represent a breadth of industrial end-users, welcome this disruption as the potential business benefits are significant. Growing on this industry foresight, the CDT will work in key markets with our supporters to ensure that AM is positioned to provide a real and lasting contribution & impact to UK manufacturing and provide economic stability and growth. This contribution will provide societal benefits to UK citizens through the generation of wealth and employment from high value manufacturing activities in the UK.

Kelly, Sarah (2020): Design rules for additively-manufactured wrist splints. Loughborough University. Thesis. https://doi.org/10.26174/thesi...;

Globally persons with disabilities have lower employment rates compared to the general population due to systemic barriers particularly in the formal sector. In developing countries, 80 percent to 90 percent of people with disabilities of working age are unemployed. There has been limited research in low-income and middle-income countries focused on the barriers to access and retain formal employment for persons with disabilities. The aim of this paper, based on desk research, is to analyse the barriers to access and retain formal employment of persons with disabilities which are framed in three categories according to where the barriers primarily manifest: 1. In the workplace among employers and co-workers without disabilities, 2. Among persons with disabilities seeking or engaged in formal employment and 3. In the wider social, physical and policy environment. Although the study mainly focuses on Kenya and Bangladesh other countries’ literature on access to and retention of employment of persons with disabilities were reviewed where relevant. In the current context where the global pandemic is breaking barriers to remote working one part of the solution will be to empower persons with disabilities with appropriate access to Information and Communication Technology, assistive devices and services, digital skills, creating more accessible and inclusive digital platforms for persons with disabilities which also hold the potential to improve working conditions and productivity for the whole workforce as well as enhancing resilience to potential future shocks.

Jahan & Holloway, 2020, Barriers to Access and Retain Formal Employment for Persons with Disabilities in Bangladesh and Kenya, GDI Hub Working Paper Series Issue 01

Approximately 15% of the world's population has a disability and 80% live in low resource-settings, often in situations of severe social isolation. Technology is often inaccessible or inappropriately designed, hence unable to fully respond to the needs of people with disabilities living in low resource settings. Also lack of awareness of technology contributes to limited access. This workshop will be a call to arms for researchers in HCI to engage with people with disabilities in low resourced settings to understand their needs and design technology that is both accessible and culturally appropriate. We will achieve this through sharing of research experiences, and exploration of challenges encountered when planning HCI4D studies featuring participants with disabilities. Thanks to the contributions of all attendees, we will build a roadmap to support researchers aiming to leverage post-colonial and participatory approaches for the development of accessible and empowering technology with truly global ambitions.

Giulia Barbareschi, Dafne Zuleima Morgado-Ramirez, Catherine Holloway, Swami Manohar Swaminathan, Aditya Vashistha, and Edward Cutrell. 2021. Disability Design and Innovation in Low Resource Settings: Addressing Inequality Through HCI. Extended Abstracts of the 2021 CHI Conference on Human Factors in Computing Systems. Association for Computing Machinery, New York, NY, USA, Article 124, 1–5. DOI:https://doi.org/10.1145/3411763.3441340

Posterior Cortical Atrophy is a rare but significant form of dementia which affects people's visual ability before their memory. This is often misdiagnosed as an eyesight rather than brain sight problem. This paper aims to address the frequent, initial misdiagnosis of this disease as a vision problem through the use of an intelligent, cost-effective, wearable system, alongside diagnosis of the more typical Alzheimer's Disease. We propose low-level features constructed from the IMU data gathered from 35 participants, while they performed a stair climbing and descending task in a real-world simulated environment. We demonstrate that with these features the machine learning models predict dementia with 87.02% accuracy. Furthermore, we investigate how system parameters, such as number of sensors, affect the prediction accuracy. This lays the groundwork for a simple clinical test to enable detection of dementia which can be carried out in the wild.